Genicom 3600 Bedienungsanleitung Seite 107
- Seite / 174
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Remove and Replace Procedures
5-21
5
To replace the TTR supply hub and TTR supply hub adjusting plate
1. Remove the two Phillips screws securing the TTR supply hub adjusting
plate to the TTR subplate and install the new adjusting plate in its place.
2. Install the thick steel washer removed in Step 5 above. Align the TTR clutch
encoder with the opening in the main deck plate and slide the TTR supply
hub back through the TTR clutch/encoder, the nylon washer, the motor
plate, and the TTR subplate.
Note: Do not remove the motor plate or subplates. Changing the position of these
plates can alter factory alignment and cause ribbon wrinkling or self-strip
problems.
3600M.056
TTR
supply hub
Snap ring
Thin
washer
TTR clutch/
encoder
Thick
washer
Nylon
washer
TTR supply
hub adjusting
plate
3. Install the thin washer removed in Step 4 and the new retaining snap rings.
4. Reattach the front bezel cover. Ensure that the media access door operates
properly (snaps firmly shut) after the front bezel cover is installed.
5. Align the ribbon supply hub as described in “Aligning the TTR Supply
Hub” in Chapter 3.
6. Reload media (and ribbon if used) and lower the printhead.
7. Install the electronics cover, the media cover, and the power cord, and
check the printer for proper operation.
- 3600 Bar Code Label Printer 1
- c39 c39 2
- Contributors 3
- Contents 5
- Troubleshooting 7
- Before You Begin 11
- Warnings and Cautions 12
- Purpose of This Manual 12
- How This Manual Is Organized 13
- Terms and Conventions 14
- Additional Information 15
- General Information 17
- Overview of the 3600 Printer 19
- 3600 Features 20
- 3600 Printer Specifications 20
- General Information 21
- Communications 22
- Fonts and Graphics 22
- Character Sets 22
- 3600 Printer Options 23
- Coax Interface 24
- Parallel Interface 24
- Network Connectivity 24
- Batch Takeup 24
- 3600M.002 25
- 3600M.003 26
- 3600M.004 27
- Media or System Faults 28
- Feed/Pause Pushbutton 28
- DIP Switch Settings 29
- Printing 30
- Using the Printer Command Set 31
- Preventive Maintenance 33
- Inspecting the Printer 36
- Cleaning the Printer 36
- Removing the Media Cover 37
- Cleaning the Printhead 38
- 3600M.012 39
- 3600M.013 40
- 3600M.015 42
- 3600M.016 43
- Cleaning the Printer Covers 44
- Testing and Adjusting 45
- Testing the Printer 47
- Setting DIP Switches 48
- 3600M.020 49
- Dot Increment Switch Settings 50
- Printing Test Labels 51
- CODE,39,3.0./1 52
- 3600M.026 53
- 3600M.028 54
- Testing and Adjusting 55
- Adjusting the Printer 57
- Printhead bias 58
- 3600M.032 59
- 3600M.033 60
- 3600M.034 61
- 3600M.035 62
- 3600M.036 63
- 3600M.037 64
- Aligning the Printer 65
- Aligning the Rollers 66
- Aligning the Printhead 67
- 3600M.040 68
- Aligning the TTR Supply Hub 69
- Troubleshooting Tips 73
- Where to Start 73
- Troubleshooting Checklist 74
- Error Handling 75
- Error Codes 76
- Printer Errors 77
- Printer Errors (continued) 78
- Printer Operation Problems 79
- Print Quality Problems 80
- Communications Problems 82
- Environmental Problems 83
- Inadequate Earth Ground 84
- Miscellaneous Problems 86
- Replacing Printer Components 89
- Main PCB 90
- Lithium 90
- Replacing the Printhead 91
- Replacing the Bezel PCB 92
- 3600M.045 93
- 3600M.046 94
- Lower outboard 96
- Tear bar 96
- Label mark 97
- Label taken 98
- 3600M.051 99
- 3600M.052 100
- 3600M.053 101
- 3600M.054 102
- Remove and Replace Procedures 103
- 3600M.055 104
- 3600M.059 112
- 3600M.060 114
- 3600M.061 116
- 3600M.063 118
- Replacing the Transformer 119
- PCB Drawings and Schematics 121
- 3600M.072 133
- 3600M.073 134
- 3600M.074 135
- 3600M.075 136
- 3600M.076 137
- Replacement Parts 140
- 3600 Manuals 146
- 3600M.091 148
- 3600M.092 149
- 3600M.093 150
- 3600M.094 151
- 3600M.095 152
- 3600M.096 153
- 3600M.097 154
- Appendix 155
- Power Supply 158
- Power Fail Detection 159
- Battery Life Calculations 159
- Motor Driver 160
- Processor 161
- Interrupt Priority Levels 162
- Static RAM 163
- Communications Interface 164
- A/D Converter 164
- DIP Switches 164
- ASIC and I/O Option Interface 164
- Front Panel Interface 165
- Debug Interface 165
- Timing Diagram 167
- Image Band Buffering 168
- Image Band Example 169
- Print Energy Compensation 172
- Font Caching Flow Chart 173
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.430 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern